GoFlight Hardware and Prepar3D v5
There are a few key areas which is causing me to take a slow approach to moving full-time over to the new Prepar3D version 5. Of course, reason number 1 is because I have such a smooth running P3Dv4.5 setup that there really isn’t any need to get in a hurry to make the move. Also as I’ve mentioned before, the PMDG 737NGXu is my favorite aircraft and one I fly most often and it most likely is still a few weeks from making it over to P3Dv5. Finally I’m also dragging my feet a bit in anticipation of the next P3Dv5 hotfix.
While all those things are certainly important to me. There is another area which also takes center stage and that is supportability of my GoFlight Hardware. I own several different external hardware components which I enjoy using when flying. As of the posting of this article, there has been no mention from GoFlight on when they plan to release an updated version of their software to support Prepar3D version 5. I’ve emailed them and received no response as of yet.
Did Some Digging
Normally I’m pretty reluctant to try to make something work in a new version of P3D until a new installer has been released. There are some who are flying around in the PMDG 737NGXu and I guess they are having fun with a few minor quirks. I don’t like minor quirks and try to avoid them at all cost. My philosophy is minor quirks now could lead to serious issues later. I just don’t have time for that.
Having said all that, I proceeded to research if any others have had success in getting it all to work and I found the answers I was looking for.
It Does Work
Oddly enough, the GoFlight Software does work fine in P3Dv5. All I needed to do was copy my .exe.xml file from my P3Dv4 instance over to P3Dv5. Of course, I made sure to first backup my P3Dv5 .exe.xml file first. Then I proceeded to copy/paste and overwrite the file. I rebooted my PC and tested.
Just FYI, the purpose of the exe.xml file serves as a set of instructions for launching various P3D addons. When I view my exe.xml file in my P3Dv4 setup, I see entries for GoFlight and also for Chaseplane. Comparing that to the v5 instance, it only showed Chaseplane. So since both GoFlight and Chaseplane are working great in v4 and I’ll use both in v5, I just simply copied the file from v4 to v5. But once again, please make a backup of the exe.xml file located in your v5 just in case.
File Location
Just copy .exe.xml located C:\Users\[username]\AppData\Roaming\Lockheed Martin\Prepar3D v4
to C:\Users\[username]\AppData\Roaming\Lockheed Martin\Prepar3D v5
This should get most GF hardware working in P3Dv5. If you own the GF MCP Pro and EFIS panels, then you’ll need to pickup the updated GFIT (GoFlight Interface Tool) from Pollypot Software. A new version has been released for P3Dv5 which does work great on the PMDG 747 QoTSII.
With this working, once the PMDG 737NGXu is officially made available for P3Dv5 I then just need to proceed with finalizing getting my yoke, pedals and throttles programmed in FSUIPC 6 and I’ll be off to the races. But until then….I’m happily flying along with my trusty P3Dv4.5 setup and she’s looking marvelous.
Until next time….
Happy Flying!!!
Jerry
Atomic
June 6, 2020 - 10:11 am
Don’t feel rushed to change over to anything in any sort of hurried time line.
If you have everything working correctly and are enjoying the add-ons etc in your current version then just enjoy it.
You can change over to 5 in your own good time when you feel it’s a good time to do so.
Once the “Quirks” are worked out and they can offer a smooth, stable version of 5 and have the add-ons you enjoy then you can start the move.
Hope all is well Jerry.